Meer specificaties, uitrusting en informatie:
Specificaties
Ontwerper: Sabre Design Team - Jim Taylor Yacht Designs
Kiel: Fin kiel
Romp type: Mono Romp
Afmetingen
Lengte over alles: 45 ft 2 in
Breedte: 14 ft 1 in
Lengte over water: 38 ft 4 in
Maximum diepgang: 6 ft 9 in
Waterverplaatsing: 26500 lbs
Ballast: 10200 lbs
Sta hoogte: 6 ft 6 in
Drooj Gewicht: 26900 lbs
Motor Opties
Engine Option 1: 1x Yanmar 4JH3-TBE Yanmar 4JH3-TBE 76 HP
Tanks
Aantal watertanks: (200 Gallons)
Aantal brandstoftanks: (100 Gallons)
Aantal afvalstoffentanks: (55 Gallons)
Interieur
Aantal enkele bedden: 7
Additional Features
- Fully equipped tool kit.
- Activated carbon water filter.
- 4 type A, B, C fire extinguishers
- Louvered main cabin locker doors.
- Cockpit locker light.
- Marelon recessed thru-hulls with Marelon sea valves.
- Hoses below the waterline are double clamped.
- Cyss hull ceilings and inlays.
- Propane 4 burner stove with oven and gas sniffer.
- Hot and cold pressure water.
- Varnished interior cherry finish.
- Automatic electric and manual bilge pumps.
- Double ice box with two lids.
- Laminated trim on shelving.
Mast
- Aluminum, keel stepped, Offshore Spars mast with triple swept airfoil saders, mast-head Delta rig with white Awlgrip finish.
- Masthead with 3 halyard sheaves and double spinnaker crane.
- Internal main and genoa halyards.
- Prewired with radio cable.
Additional Description
- Three 12 volt deep cycle marine batteries (2-200AH, 1-100AH).
- (2) 30A-110V shore power system.
- (2) 50 foot shore power cord.
- Master AC/DC Bass marine circuit breaker panels.
- All wiring is color coded and meets USCG standards.
- Cabin courtesy lights
Additional Description
- Yanmar 76HP - 4 cylinder fresh water cooled diesel with reduction gear. Electrical shut-off.
- Two 12 volt 80 amp alternators
- 100 gallon custom aluminum fuel tank, deck filled, shut-off valve, vented and grounded.
- Racor fuel filter/water separator.
- Flexible 4 point engine mount system.
- 1.375" Aquamet prop shaft passes through a glassed in PYI shaft seal with bronze strut.
Additional Description
- Single unit, closed cell PVC foam cored, hand-laminated fiberglass of alternate layers of mat knitted biaxial roving.
- Isopthalic gelcoat above waterline.
- Below waterline, Sabre technology is utilized, consisting of chopped strand glass and vinylester resin as a back up for ISO NPG gelcoat.
- Internal deck to hull joint.
- Molded in double boot and cove stripes.
- Bulkheads, berth faces, shelves and floor stringers laminated to hull providing integral, structural strength.
- Step transom
Additional Description
- Single unit, hand-laminated fiberglass with closed cell PVC foam core for stiffness, and marine mahogany plywood in lieu of foam in high stress areas.
- The deck is bonded to the hull using stainless steel thru bolts every 6."
3M 5200 fills the deck to hull joint.
Keel
- A modern NACA section fin keel cast in lead with antimony added for strength.
- Thru-bolted to reinforced keel sump with stainless steel bolts.
(remove)
